 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| PRELIMINARY CYIWOSC1300AA 1.3 Megapixel CMOS Sensor Features * * * * * * * * * * * 1.3-megapixel resolution (1297H x 1041V) 2.8 x 2.8 pixel size 1/4" optical format image sensor Progressive scan On-board readout sequencer Up to 17 frames per second at full resolution Fast preview/snapshot switching with dynamic power management Bidirectional serial command interface 10-bit parallel data port Low-power high frame rate preview mode Programmable frame size/rate, gain, exposure, blanking, left-right and up-down image reversal, windowing, auto black level offset correction, and panning Table 0-1. Key Performance Parameters Parameter Pixel size Array format Imaging area Color filter array Optical format Frame rate Scan mode Sensitivity Dynamic range Shutter type ADC Programmable controls Typical Value 2.8 x 2.8 1297H x 1041V 3.6 mm x 2.9 mm RGB Bayer 1/4 inch 15 fps @ 1280H x 1024V 60 fps @ 640H x 480V Progressive TBA TBA Electronic rolling shutter 10-bit Frame size, frame rate, gain, exposure, black, offset correction, all directions image flipping LED and Xenon 24 Mps @ 24-MHz clock 4-27 MHz 64 s-66 ms 2.65-3.1V / 1.8V Analog: 2.6-3.1V Digital: 1.7-1.9V or 2.65-3.1V IO: 1.7-3.1V TBA -20 to +70C TBA Applications * * * * * Cellular phone camera modules Pocket PCs PDAs Toys Battery operated device Flash support Pixel rate Input clock range Exposure time range On-chip voltage regulator Supply voltage Power consumption Operating temperature Package CypressSemiconductorCorporation Document #: 38-19008 Rev. *A * 198 Champion Court * SanJose, CA 95134-1709 * 408-943-2600 Revised August 22, 2005 PRELIMINARY TABLE OF CONTENTS CYIWOSC1300AA FEATURES .............................................................................................................................................................1 APPLICATIONS .....................................................................................................................................................1 1.0 GENERAL DESCRIPTION ...............................................................................................................................4 2.0 FUNCTIONAL OVERVIEW ..............................................................................................................................5 3.0 SIGNAL DESCRIPTION ...................................................................................................................................6 4.0 PIXEL ARRAY STRUCTURE ...........................................................................................................................7 5.0 TYPICAL USE SCENARIO ..............................................................................................................................8 6.0 DATA READ OUT ............................................................................................................................................9 6.1 Frame Timing ................................................................................................................................................................ 9 6.2 Frame Sequence Structure ......................................................................................................................................... 10 6.3 Controlling the Sequencer ........................................................................................................................................... 11 7.0 SERIAL BUS DESCRIPTION ......................................................................................................................... 12 7.1 16-bit Write Access Procedure .................................................................................................................................... 12 7.2 16-bit Read Access Procedure .................................................................................................................................... 12 7.3 8-bit Write Access Procedure ...................................................................................................................................... 13 7.4 8-bit Read Access Procedure ...................................................................................................................................... 14 8.0 REGISTERS ................................................................................................................................................... 15 8.1 Register Map ............................................................................................................................................................... 15 9.0 FEATURE DESCRIPTIONS ........................................................................................................................... 26 9.1 Efficient Well Pixel ....................................................................................................................................................... 26 9.2 Windowing ................................................................................................................................................................... 26 9.3 Subsampling ................................................................................................................................................................ 26 9.4 Flash Synchronization ................................................................................................................................................. 26 9.5 Xenon Flash ................................................................................................................................................................ 26 9.6 LED Flash .................................................................................................................................................................... 27 9.7 Normal Operation Mode .............................................................................................................................................. 27 9.8 Standby Mode ............................................................................................................................................................. 27 9.9 Idle Mode ..................................................................................................................................................................... 27 9.10 Readout Modes ......................................................................................................................................................... 27 9.11 Viewfinder Mode ........................................................................................................................................................ 28 9.12 Snapshot Mode ......................................................................................................................................................... 28 9.13 Power-on Reset ......................................................................................................................................................... 28 9.14 On-Chip Pixel Binning ............................................................................................................................................... 28 10.0 1.3MP IMAGER PAD NUMBERING ............................................................................................................. 29 11.0 ELECTRICAL SPECIFICATIONS ................................................................................................................ 31 11.1 Absolute Maximum Ratings ....................................................................................................................................... 31 11.2 Operating Conditions ................................................................................................................................................. 31 11.3 Electrical Characteristics ........................................................................................................................................... 31 12.0 ENVIRONMENTAL SPECIFICATIONS ........................................................................................................ 31 Document #: 38-19008 Rev. *A Page 2 of 31 PRELIMINARY LIST OF FIGURES CYIWOSC1300AA Figure 1-1. Block Diagram ....................................................................................................................................... 4 Figure 2-1. Typical Configuration using On-chip Regulator ..................................................................................... 5 Figure 2-2. Typical Configuration without On-chip Regulator .................................................................................. 5 Figure 4-1. Pixel Array .............................................................................................................................................7 Figure 5-1. Typical Usage........................................................................................................................................ 8 Figure 6-1. Regular Frame Readout Sequence with Accompanying Signals .......................................................... 9 Figure 6-2. FRAME and LINE Timing ......................................................................................................................9 Figure 6-3. Horizontal Timing with PIX_CLK the Inverse of the Internal Chip Clock CLK ....................................... 9 Figure 6-4. Typical Frame Sequence..................................................................................................................... 10 Figure 6-5. Frame Sequence with Addition of a Very Large Number of Dummy Lines ......................................... 10 Figure 7-1. 16-bit Write .......................................................................................................................................... 13 Figure 7-2. 16-bit Read .......................................................................................................................................... 13 Figure 7-3. 8-bit Write ............................................................................................................................................ 13 Figure 7-4. 8-bit Read ............................................................................................................................................ 14 Figure 9-1. Xenon Flash Frame Sequence ............................................................................................................ 26 Figure 9-2. Xenon Flash Sequence with Accelerated Initial Reset ........................................................................ 26 Figure 9-3. Xenon FLASH Strobe Timing Configuration ........................................................................................ 27 LIST OF TABLES Table 0-1. Key Performance Parameters ...............................................................................................................1 Table 10-1. Pin Map Table (Left Side) .................................................................................................................. 29 Table 10-2. Pin Map Table (Right Side) ................................................................................................................ 30 Table 11-1. ............................................................................................................................................................ 31 Table 12-1. ............................................................................................................................................................ 31 Document #: 38-19008 Rev. *A Page 3 of 31 PRELIMINARY 1.0 General Description CYIWOSC1300AA Cypress Semiconductor Corporation's (Cypress's) CYIWOSC1300AA is a 1.3-megapixel (SXGA) CMOS digital image sensor. It has a 1/4-inch active-pixel format, with an active imaging pixel array of 1297x1041 pixels and on-board readout sequencer. The device captures Bayer-pattern color still pictures, and offers a low-power video preview mode. Defective pixels are interpolated instantaneously to make them invisible in the output image. Most of the chip's image readout parameters are doubled-up into two separate records, allowing the user to change from preview mode to snapshot and back in a minimum of time. The imager also integrates features like programmable gain/exposure control and black level calibration. The sensor equips cameras with a frame rate of up to 15 fps at full resolution and image windowing to any size, while sustaining smooth, continuous video preview at reduced power consumption. The CMOS technology has the advantage of having a smaller form factor, lower power consumption, lower cost and ease of design compared to CCD. The 1.3-Mp sensor operates in a system accepting commands from a bidirectional serial interface and deliver raw single images or video-like streams of raw Bayer-patterned images through a 10-bit parallel data interface. The low-power viewfinder mode enhances the support for battery-operated platforms. Automatic flash sequencing and single-supply operation provides reduced complexity of the camera system. The device runs off an external clock, ideally in the range of 20 to 27 MHz. This sensor has no micro-lenses and yet can achieve a 70% fillfactor ratio, using Cypress proprietary process technology. It helps increase process yield and lower system cost. Figure 1-1. Block Diagram Document #: 38-19008 Rev. *A Page 4 of 31 PRELIMINARY 2.0 Functional Overview CYIWOSC1300AA The analog core of the chip is comprised of the actual image sensor with its column amplifiers and addressing logic, and an analog processing block with a Programmable Gain Amplifier (PGA), and a 10-bit ADC. The column amplifiers perform double sampling on the pixel signals, thus reducing fixed pattern noise due to pixel non-uniformity. The output of the column amplifiers is a single analog signal stream of Bayer-colored pixels, which is sent to the PGA for additional gain and offset conditioning. The single ADC accepts this stream and turns it into a 10-bit digitized stream of Bayer-colored pixel values. The readout sequencer performs automated readout of images with given exposure time and gain settings. Mirrored readout and frame time adjustments are programmable. Most of the chip's image readout parameters are doubled-up into two separate records, allowing the user to change from preview mode to snapshot and back in a minimum of time. The output from the sensor is a Bayer pattern: alternate rows are a sequence of either green/red pixels or blue/green pixels. The offset and gain stages of the analog signal chain provide per-color control of the pixel data. Analog supply 2.65-3.1V Master clock Standby CMD_D CMD_CLK CMD_A CLK STANDBY CMD_D CMD_CLK CMD_A REG_BYPASS VDD_28 VAA 1kO 1uF VAA_PIX Digital supply 2.65-3.1V PIX_OE_n PIX_D[9:0] PIX_CLK LINE FRAME FLASH VDD_18_O 1uF GND Figure2-1 shows a typical module wiring diagram. When using the on-chip regulator REG_BYPASS has to be connected to ground. VDD_28 can be connected to a 2.65-3.1V supply like all other power supplies. There must be sufficient decoupling on the supplies to insure clean supply voltages. Note that RESET_N is typically connected with an RC circuit to hold RESET_N low until all power supplies have reached their proper level. Analog supply 2.65-3.1V Master clock Standby CMD_D CMD_CLK CMD_A CLK STANDBY CMD_D CMD_CLK CMD_A REG_BYPASS 1.8V VDD_28 VAA 1kO 1uF VAA_PIX Digital supply 2.65-3.1V PIX_OE_n PIX_D[9:0] PIX_CLK LINE FRAME FLASH VDD_18_O 1uF GND PIX_OE_n PIX_D[9:0] PIX_CLK LINE FRAME FLASH RESET_N VDDIO 10uF 1uF 1uF AGND DGND PIX_OE_n PIX_D[9:0] PIX_CLK LINE FRAME FLASH Analog ground Logic ground Figure 2-2. Typical Configuration without On-chip Regulator Figure2-2 shows a typical module wiring diagram. When not using the on-chip regulator REG_BYPASS and the VDD_28 have to be connected to their appropriate levels. VDD_28 has to be connected to a 1.8V supply. There must be sufficient decoupling on the supplies to insure clean supply voltages. Note that RESET_N is typically connected with an RC circuit to hold RESET_N low until all power supplies have reached their proper level. RESET_N VDDIO 10uF 1uF 1uF AGND DGND Analog ground Logic ground Figure 2-1. Typical Configuration using On-chip Regulator Document #: 38-19008 Rev. *A Page 5 of 31 PRELIMINARY 3.0 Signal Description I/O I I I I/O I I I O/Z O/Z O/Z O/Z O/Z O/Z PWR PWR GND PWR GND PWR GND #Pins 1 1 1 1 1 1 1 10 1 2 1 1 1 2 1 3 1 1 1 2 1 2 3 3 1 Function System clock, 4 .. 27 MHz Asynchronous reset Turns off device Interface serial data in and out Interface bit clock, up to 400 kHz CYIWOSC1300AA Signal Name CLK RESET_n STANDBY CMD_D CMD_CLK CMD_A PIX_OE_n PIX_D[9:0] PIX_CLK EXT[1:0] FRAME LINE FLASH VAA VAA_PIX AGND VAA_DIG AGND_DIG VDD_28 DGND Interface device address selector Output enable for PIX_D, PIX_CLK, FRAME, LINE, EXT, FLASH Output pixel data Output pixel data word clock Extension port for debug Frame valid strobe Line valid strobe Flash strobe Sensor core/ADC analog supply (2.65-3.1V) Pixel array supply (2.65-3.1V) Sensor core/ADC analog ground Sensor core digital supply (2.65-3.1V) Sensor core/ADC digital ground Raw logic supply in; connect to 2.65-3.1V when regulator is used, otherwise to 1.7-1.9V Logic ground Puts regulator in bypass, use only when VDD_28 = 1.8V Regulated 1.8V logic supply out; connect to bypass capacitor only (two pads, for bonding to one package pin) IO supply (1.7-3.1V) IO ground Internal reset net out (POR test only) REG_BYPASS I VDD_18_O PWR VDDIO DGNDIO RESET_OUT PWR GND O Document #: 38-19008 Rev. *A Page 6 of 31 PRELIMINARY 4.0 Pixel Array Structure CYIWOSC1300AA The sensor device is a camera on a CMOS chip imager with 1.3-megapixel resolution (SXGA) in a 1/4" optical format. Figure4-1 below shows the layout of the Pixel Array. The pixel plane consists of a total of 1041 lines, numbered 0 to 1040, each of 1297 pixels, numbered 0 to 1296. All lines are sensitive to light and pixels are optically active and addressable. All pixels can be addressed for readout. A border of width 8 at the periphery of the array, the overscan area, will be used only for image processing boundary conditioning, while the central 1281x1025 area can be output to the end-user. The number of lines and pixels is odd to assure invariance of color pattern when mirrored readout is used. The sensor is designed with a mosaic of color filters arranged in a standard Bayer pattern shown in Figure4-1. The even numbered columns contain green and red pixels and the even rows contain red and green pixels. The imager will output either all Bayer patterned pixels or all physical pixels based upon register settings. 1297 pixels GRGRG BGBGB GRGRG BGBGB 1281 Pixels GRGRG BGBGB GRGRG BGBGB 1041 lines 1025 Lines GRG BGB GRG BGB RG GB RG GB GRG BGB GRG BGB RG GB RG GB 8 overscan lines 8 overscan pixels Figure 4-1. Pixel Array Document #: 38-19008 Rev. *A Page 7 of 31 PRELIMINARY 5.0 Typical Use Scenario CYIWOSC1300AA These commands cause the sensor chip to: 1. Stop the present image acquisition 2. If the present image was an incomplete acquisition, eliminate any effect its data might have on the ISP (red frame in the figure). 3. Reconfigure itself for high-quality, high-power, full-frame image capture. 4. Capture a short sequence of images, one or more of them to be written by the application processor into cellphone memory 5. When finished, await a new command to re-enter the preview mode. The following describes a typical scenario of camera usage. The camera starts in a viewfinder mode, displaying images at video rate (15 to 30 frames/s) on the mobile application LCD. As LCDs are typically of low resolution and low accuracy, the sensor can be run at a smaller image size and a lower image quality. This then allows power consumption to be reduced. This is relevant in a battery-powered application, as most users will run their cameras in viewfinder/preview mode for 99% of the camera-on time. When the end-user then wants to take a picture and store it in the camera's memory, he pushes the shutter release button. This action is communicated to the application processor, which then sends a stream of commands to the sensor chip. Shutter button Sensor commands Camera mode Images Data target Time Seconds, minutes 200 milliseconds LCD Application memory LCD Preview subsampled, low power , trans snapshot , high quality, high power idle Preview ... , Figure 5-1. Typical Usage Document #: 38-19008 Rev. *A Page 8 of 31 PRELIMINARY 6.0 Data Read Out Assert FRAME CYIWOSC1300AA The imager is read out in a progressive scan fashion. This means that each successive row is read out in an increasing row number. The data are digitized via on-chip A/D converters and the output resolution is at a 10-bit resolution. All of the lines are scanned at the same speed, all of them being scanned in the line time. The frame rate is the inverse of the total sum of line times, and the maximum exposure time is the total sum of line times. The resolution is set by three factors. The resolution may be decreased by sub-windowing a smaller region of interest (ROI) as set in the internal registers. The imager can also be programmed to sub-sample the array to read out as much as at a 4-time rate. In 4x4 subsampling mode both lines and pixels are read in a 1:1:0:0:0:0:0:0 pattern (read-2-skip-6). This quarters the number of lines in a frame, as well as the number of pixels in a line. Also a 2x2 subsampling mode is user programmable. Finally, the imager can be programmed to bin (combine) adjacent pixels of similar color in one direction with strength of2. Line blanking time Deassert LINE Assert LINE Physical lines ROI of valid pixels Line blanking time Dummy Lines Deassert FRAME Physical pixels Dummy Pixels Line time = Line blanking time + valid pixels time + dummy pixels time 6.1 Frame Timing Figure6-1 shows a regular frame readout sequence with accompanying strobe signals. The FRAME and LINE strobe signals depend on the LN_FORM and FR_FORM register settings. We assume here that they are both set to 1. The FRAME pulse is asserted at the start of the first line that is physically read from the pixel array. This and the following lines are typically overscan lines used for preconditioning processing pipelines. These overscan areas are defined by the physical pixel area as shown in Figure6-1. FRAME is not asserted whenever the present image is blanked out (see *_BLANK_FIRST and *_BLANK_PERIOD). LINE is asserted to qualify those lines that belong to the ROI, and is asserted at the first pixel in the ROI of each such line. LINE is deasserted at the last pixel belonging to the ROI. FRAME is deasserted at the last line and last pixel of the overscan area, or the lowerright edge of the physically-scanned area. As can be seen from Figure6-1 it is possible to set a number of dummy lines/pixels. These pixels will follow the same Figure 6-1. Regular Frame Readout Sequence with Accompanying Signals readout rate as the pixels in the ROI but will fall outside the Line/FRAME pulses. Therefore they should be discarded by the camera system. The number of dummy lines/pixels is programmable to set integration times longer than the ROI readout time and to give the accompanying peripheral devices (e.g., ISP) time to process the image data. The minimum amount of dummy pixels/lines should be a multiple of 8. Using the appropriate registers the number of overscan pixels (physical pixels) is also programmable for image processing boundary conditioning. Figure6-2 indicates the timing of the FRAME and LINE synchronization signals relative to the datastream on the PIX_D bus. Figure6-3 depicts the horizontal/pixel timing on the parallel data interface. FRAME LINE P I X _ D [9 :0 ] XX LINE 1 00 h LINE 2 L I N E n -1 0 0h LINE n 00 h Figure 6-2. FRAME and LINE Timing CLK PIX _C L K LINE P I X _D [9:0] XX Figure 6-3. Horizontal Timing with PIX_CLK the Inverse of the Internal Chip Clock CLK Document #: 38-19008 Rev. *A Page 9 of 31 PRELIMINARY PIX_D bytes change state on a falling edge of PIX_CLK, and are to be sampled on the rising edge, or vice versa, as programmed by the user. PIX_CLK is active for all physically scanned pixels (also for dummy pixels) and is inactive during line blanking intervals. PIX_CLK is a gated and possibly inverted copy of the internal chip clock. In normal operation the internal clock is equal to the system clock CLK, but in low-power operation the internal clock, and thus PIX_CLK, can be divided by 2 or 4. CYIWOSC1300AA In Figure6-4, the shutter time is considerably shorter than the frame time. A moderate amount of dummy lines is included, extending the frame time somewhat. As the diagram indicates, the acquisition of a sequence of frames is a periodic, regular process: at all times is one line of a particular frame being read, while a line belonging to that same frame, or to the next frame, is being reset. The one exception to this rule is during sequence initialization: the first N lines (N corresponding to the desired exposure time) of the first frame are reset, while no lines of frame 1 are being read. Figure6-5 illustrates a typical frame sequence with the exposure/shutter time (almost) equal to the total frame time. This increases the maximally-allowed exposure time much more than in previous diagrams, while the frame rate is severely reduced. It illustrates increased exposure time at the cost of a lowered frame rate. This is only to be done when sufficient light is lacking and when the camera is held stable. 6.2 6.2.1 Frame Sequence Structure Overview The acquisition of a number of frames is an operation that is started by the CCP (camera control processor), following which the sequencer first initializes the sequence, then takes the frames in a regular, periodic fashion, and (when needed) terminates the sequence. The frame sequence itself can be adorned by optional attributes such as blanking out of a specific number of frames, blanking out of bad frames, Xenon flash ignition between two frames, etc. Within the sequence of frames will be specific synchronization points for updating image-sensitive parameters such as exposure time and gain, without disrupting the frame sequence itself. 6.2.2 Frame Timelines Examples 6.3 Controlling the Sequencer An image or sequence acquisition is started when a positive edge is seen on the RUN bit in the CCP_CTRL register. When CCP_CTRL is updated with a RUN transition from '0' to '1' (or remains at '1', see AUTO_START bit), any present image acquisition sequence is stopped (also see FAST_STOP bit) and a new acquisition is started in a potentially new record (see CTXT bit). A frame sequence ends normally when the frame counter (N_FRAMES) is at zero after the last (dummy) line of a frame has been produced be the sequencer. Deassertion of RUN at any time makes the sequencer finish its present line, after which it stops scanning and enters its idle state (also see FAST_STOP bit in the CCP _CTRL register). The following timelines indicate a number of possible scenarios. The lower/orange band in each diagram houses the periods during which the lines of a frame are reset (top to bottom), the upper/green band the periods during which the lines are read out (top to bottom). The frame size is kept constant (number of valid lines), but the number of dummy lines is varied to demonstrate several concepts of readout. Line reads per frame Line resets per frame Time Frame 1 Dummy 1 Frame 2 Frame 2 Dummy 2 Frame 3 Frame 3 Dummy 3 Frame 1 Dummy 1 Dummy 2 Dummy 3 Shutter time Frame time Figure 6-4. Typical Frame Sequence Line reads per frame Line resets per frame Time Shutter time Frame 1 Dummy 1 Frame 1 Frame 2 Dummy 1 Dummy 2 Dummy 2 Frame time Figure 6-5. Frame Sequence with Addition of a Very Large Number of Dummy Lines Document #: 38-19008 Rev. *A Page 10 of 31 PRELIMINARY 7.0 Serial Bus Description CYIWOSC1300AA The CYIWOSC1300AA interfaces with an external ISP through a bidirectional serial command interface and a unidirectional parallel data bus, in addition to a small number of direct-control pins for frame, line and flash synchronization, for device reset, for regulator configuration, and for the standby mode. The device requires an external clock oscillator (up to 27 MHz) and a small number of strap connections to configure the device. All I/O is CMOS IO with a programmable voltage range of 1.7-3.1V. All logic inputs have no leakage when they are driven high while the chip supply voltage is low/off. The device control interface is compatible with the Philips I2C version 2.1 bus specification. The device acts as a slave only, requiring the system host to act as the master. The device address can be selected from two addresses that are hard-wired on the chip, enabling the use of up to two identical devices simultaneously on the same bus. The address selection happens with the CMD_A pin. CMD_A 0 1 Internal I2C Device Address 0xD2 0xD4 * An acknowledge or no-acknowledge bit: This is the way for the receiver (either the slave in write mode or the master in read mode) to acknowledge the data sent by the transmitter. The master generates the acknowledge clock pulse. When the receiver pulls down the data line during that clock pulse, the previous byte is acknowledged. When the data line is not pulled down, the previous byte is NOT acknowledged. A no-acknowledge is used to terminate a read or a write sequence. * An 8-bit message (register address or data byte): One data bit is transferred during each clock pulse. Data is always transferred 8 bits at a time, starting with the MSB bit, during 8 consecutive clock cycles, followed by an acknowledge bit. * A stop bit: The stop bit is defined as a LOW-to-HIGH transition of the data line while the clock line is HIGH. Except for the start and the stop bit, the data pin must always be stable during the HIGH period of the serial interface clock. It can only change when the clock is LOW. 7.1 16-bit Write Access Procedure A 16-bit write access is performed as follows 1. The master sends a Start bit. 2. The master sends the 8-bit slave device address. The last bit will be set to "0". 3. The slave acknowledges the address by sending the acknowledge bit back to the master. 4. The master sends the 8-bit register address to which a write should take place. 5. The slave sends an acknowledge bit to indicate that the register address was correctly received. 6. The master then transfers the data, 8 bits at a time. Internally, all register addresses have 16 bits, thus requiring two 8-bit transfers to write to one register. 7. The slave acknowledges every 8-bit word. 8. After every two 8-bit words written, the register address is automatically incremented, so that the next 16 bits are written to the next register address. 9. Steps 6, 7, and 8 are repeated for writing batches of data on consecutive register addresses. 10.The master stops the access by sending a Start or a Stop bit. Figure7-1 gives an example of a 16-Bit write access (value 0x310b) to register 0x2a. The D2h address is the same slave address as used on Cypress's programmable clock chips. This address does not collide with the most obvious competing image sensor chips. The D4h address is an arbitrary modification of the device address to allow two identical sensor chips on the same command bus. The command interface supports writing to and reading from 16-bit internal registers, with 8-bit address locations, at speeds of up to 400 kbits/s. The interface clock CMD_CLK and the address pin CMD_A are driven by the serial interface master. The data pin is pulled up to a positive supply voltage by an off-chip resistor and can be pulled down both by the master and the slave device. The serial interface protocol determines which device can drive the data pin at any given time. Data transfers to/from each 16-bit register can be 16 bits at once, the upper 8 bits, or the lower 8 bits. After any complete 16-bit transfer the internal register address is incremented automatically, anticipating the next similar transfer. There is no auto address increment for 8 bit transfers. The bus is idle when both the CMD_CLK and CMD_D pins are HIGH. Control of the bus is initiated by a start bit (beginning of an access) and the bus is released again with a stop bit (end of the access). Only the master can generate these signals. The transmission protocol defines several transmission codes: * A start bit: The start bit is defined as a HIGH-to-LOW transition of the data line when the clock line is HIGH. * The slave 8-bit address: The 7 MSB bits contain the device address: 0xD4 when CMD_A is HIGH and 0xD2 when CMD_A is LOW. The LSB bit of this address determines whether the request is a write (value is "0") or a read (value is "1"). 7.2 16-bit Read Access Procedure A typical 16-bit read access is performed as follows: 1. The master sends a Start bit. 2. The master sends the 8-bit slave device address. The last bit will be set to "0" because the register address will be written first. 3. The slave acknowledges the address by sending the acknowledge bit back to the master. 4. The master sends the 8-bit register address to which a read should take place. Document #: 38-19008 Rev. *A Page 11 of 31 PRELIMINARY CYIWOSC1300AA CMD_CLK CMD_D Start 0xD2 Device address Ack 0x2A Register address Ack 0x31 8 MSB bits Ack 0x0B 8 LSB bits Ack Stop Figure 7-1. 16-bit Write CMD_CLK CMD_D 0xD2 Device address Start Ack 0x2A Register address Ack Start 0xD3 Device address Ack 0x31 8 MSB bits Ack 0x0B 8 LSB bits NAck Stop Figure 7-2. 16-bit Read 5. The slave sends an acknowledge bit to indicate that the bits to the special register (0xF1). The register is not updated register address was correctly received. The write access until all 16 bits have been written. It is not possible to update to set the register address is now finished. just half of a register. 6. The master sends a new Start bit. 7. The master sends the 8-bit slave device address. The last bit will be set to "1" for the actual read accesses. 8. The slaves transfers the data, 8 bits at a time. Internally, all register addresses have 16 bits, thus requiring two 8-bit transfers to read one register. 9. The master acknowledges every 8-bit word. 10.After every two data bytes written, the register address is automatically incremented, so that the next 16 bits are read from the next register address. 11.Steps 8, 9, and 10 are repeated for reading batches of data on consecutive addresses. 12.The data transfer is stopped when the master or slave sends a no-acknowledge bit. 13.The master generates a Start or Stop bit to finish the read access. An 8-bit write access is performed as follows 1. The master sends a Start bit. 2. The master sends the 8 bit slave device address. The last bit will be set to "0". 3. The slave acknowledges the address by sending the acknowledge bit back to the master. 4. The master sends the 8-bit register address to which a write should take place. 5. The slave sends an acknowledge bit to indicate that the register address was correctly received. 6. The master then transfers the 8 MSB bits of the data. 7. The slave acknowledges the 8-bit word. 8. The master sends a Stop bit when the second part of the word is not written immediately. 9. Steps 1 to 8 are repeated for writing the 8 LSB bits. The only differences are the usage of the special address register (0xf1) instead of the real register address and replacing the MSB bits by the LSB bits. The register address and the 8 MSB bits need to be stored temporarily. 7.3 8-bit Write Access Procedure To be able to write one byte at a time to the register, a special register address is added. The 8-bit write is started by writing the 8 MSB bits to the desired register, then writing the lower 8 C M D_ C L K C M D_ D Start 0 xD 2 Device address Ack 0x 2A Register address Ack 0 x3 1 8 MSB bits Ack C M D_ C L K C M D_ D Start 0x D 2 Device address Ack 0 x F1 Register address Ack 0x 0B 8 LSB bits Ack Stop Figure 7-3. 8-bit Write Document #: 38-19008 Rev. *A Page 12 of 31 PRELIMINARY 7.4 8-bit Read Access Procedure CYIWOSC1300AA To read one byte at a time, the same special register address is used for the lower byte. The 8 MSB bits are read from the desired register. By following this with a read from the special register, the 8 LSB bits are accessed. The master sets the noacknowledge bits shown. A typical 8-bit read access is performed as follows: 1. The master sends a Start bit. 2. The master sends the 8-bit slave device address. The last bit will be set to "0" because the register address will be written first. 3. The slave acknowledges the address by sending the acknowledge bit back to the master. 4. The master sends the 8-bit register address to which a read should take place. 5. The slave sends an acknowledge bit to indicate that the register address was correctly received. The write access to set the register address is now finished. 6. The master sends a new Start bit. 7. The master sends the 8-bit slave device address. The last bit will be set to "1" for the actual read accesses. 8. The slaves transfers the 8 MSB bits. 9. The master sends a no-acknowledge. Steps 1 to 9 are repeated for the read procedure of the 8 LSB bits. This time, the register address used is the special register address (0xf1) and the slave will return the 8 LSB bits. CMD_CLK CMD_D 0xD2 Device address Start Ack 0x2A Register address Ack Start 0xD3 Device address Ack 0x31 8 MSB bits NAck CMD_CLK CMD_D 0xD2 Device address Start Ack 0xF1 Register address Ack Start 0xD3 Device address Ack 0x0B 8 LSB bits NAck Stop Figure 7-4. 8-bit Read Document #: 38-19008 Rev. *A Page 13 of 31 PRELIMINARY 8.0 8.1 CYIWOSC1300AA Registers Register Map The imager has 8-bit-wide register addresses that contain 16-bit-wide register values. All registers are explained in the tables below. Address 0 1 3 4 5 6 16 17 18 19 22 23 24 25 26 27 28 29 30 31 32 33 34 38 39 40 41 42 43 Register Name CONFIG1 CCP_ID CCP_CTRL CCP_CONFIG CCP_GLOBAL CCP_STAT CONFIG2 CONFIG3 CONFIG4 CONFIG5 CONFIG6 SEQ_A_FRAMES SEQ_B_FRAMES SEQ_A_ORIG SEQ_B_ORIG SEQ_A_SIZE SEQ_B_SIZE SEQ_A_ORIG_ROI SEQ_B_ORIG_RO SEQ_A_SIZE_ROI SEQ_B_SIZE_ROI SEQ_A_DUMMY SEQ_B_DUMMY SEQ_FLASH1 SEQ_FLASH2 CONFIG7 CONFIG8 CONFIG9 CONFIG10 Reset Value 0x0000 0x0350 0x0000 0x0000 0x0000 0x0000 0x5F9C 0x0077 0x0077 0x0077 0x0777 0x0000 0x0000 0x0000 0x0000 0x82A2 0x82A2 0x0101 0x0101 0x80A0 0x80A0 0x0100 0x0100 0x0041 0x0011 0x2F85 0x4C7E 0x1097 0x000A R/W R/W R/R/W R/W R/W R/R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Description configuration register 1, only upload value as described in this table device identification code camera control register (start/stop, record switch, Xenon flash) camera control configuration register (record clock division, Xenon flash arming) camera control global settings (gain change synchronization, subsampling, binning, LED flash control) camera control status (record, clock, and run status) Configuration register 2, see CONFIG2 table below for more details Configuration register 3 see CONFIG3 table below for more details Configuration register 4 see CONFIG4 table below for more details Configuration register 5 see CONFIG5 table below for more details Configuration register 6, see CONFIG6 table below for more details record A number of frames to grab and blank frame(s) configuration record B number of frames to grab and blank frame(s) configuration record A start of physical scan window record B start of physical scan window record A size of physical scan window record B size of physical scan window record A start of region of interest window record B start of region of interest window record A size of ROI window record B size of ROI window record A number of dummy lines and pixels record B number of dummy lines and pixels flash configuration 1: flash firing delay, Xenon strobe length flash configuration 2: flash frame definition, number of frames to flash in Configuration register 7, see CONFIG7 table below for more details Configuration register 8, see CONFIG8 table below for more details Configuration register 9, see CONFIG9 table below for more details configuration register 10, only upload value as described in this table Document #: 38-19008 Rev. *A Page 14 of 31 PRELIMINARY Address 44 45 46 64 128 241 Register Name SEQ_STATUS SEQ_EXP SEQ_GAIN OUT_CONFIG ISP_DEFECT ACCESS_MODE Reset Value 0x0000 0x0400 0x3F80 0x0000 0x0002 0x0000 R/W R/R/W R/W R/W R/W R/W Description CYIWOSC1300AA sequencer status and BIST result: present black residue, BIST result, flicker detection results exposure time gain and offset for preamp and PGA output interface configuration: timing and polarity of PIX_CLK, FRAME, LINE defect pixel interpolator configuration special access mode register for 8-bit serial register read and write Clients / Description Interface registers Device identification code revision 1 - imager 6 - VGA Address 1 Bits 3:0 5:4 11:6 15:12 Address 3 Bits 0 Register Name CCP_ID REV[3:0] TYPE[1:0] FORMAT[5:0] PROCESS[3:0] Register Name CCP_CTRL RUN Reset Value 0x0350 0d 1d 13d 0d Reset Value 0x0000 0 R/W R/- R/W Clients / Description Central chip control register When CCP_CTRL is updated and RUN transitions from '0' to '1' (or remains at '1', see AUTO_START bit), any present image acquisition sequence is stopped (also see FAST_STOP bit) and a new acquisition is started in a potentially new record (see CTXT bit). When CCP_CTRL is updated and RUN transitions to '0' the present acquisition is stopped and the sensor enters idle/sleep mode (see FAST_STOP). When CCP_CTRL is updated and no new RUN condition exists the present acquisition is stopped and the sensor enters idle/sleep mode (see FAST_STOP). 0 - record A: execute commanded image acquisition using record A register settings 1 - record B: execute commanded image acquisition using record B register settings 0 - when an acquisition in record B ends (also see register SEQ_B_FRAMES), no auto record return to A is done. 1 - automatically return to record A, and start a new acquisition there, when record B has finished its image acquisition sequence (see SEQ_B_FRAMES). This allows to execute a fully automatic preview-snapshot-preview sequence. Chooses between starting an acquisition when RUN is explicitly set, or whenever CCP_CTRL is written. 0 - RUN bit needs a transition from 0 to 1 to trigger an image acquisition 1 - RUN bit is level sensitive: any writing to CCP_CTRL with RUN = '1' will stop the present acquisition and start a new one 1 CTXT 0 2 AUTO_CTXT 0 3 AUTO_START 0 Document #: 38-19008 Rev. *A Page 15 of 31 PRELIMINARY Address 4 Register Name FAST_STOP Reset Value 0 R/W Clients / Description CYIWOSC1300AA 0 - finish present frame completely when asked to stop or restart 1 - accelerated stop procedure, aborting present frame quickly (also see SEQ_CONFIG2.ABORT_DUMMY) 0 - no Xenon flash 1 - fire Xenon flash when a new image acquisition starts (and Xenon flash has been armed in the record of that new acquisition, see 0:4 CCP_CONFIG) 0 - chip operational 1 - execute a soft reset, which resets this register too; the other chip parameter registers are not reset. R/W R/W Clients / Description CCP configuration record B internal clock division: "00" - /1 "01" - /2 "10" - /4 "11" - N/A set to /1 if record B is to be used for snapshot image capture (recommended) record A internal clock division: "00" - /1 "01" - /2 "10" - /4 "11" - N/A set to /2 or /4 if record A is to be used for video preview (recommended) idle mode internal clock division: "00" - /1 "01" - /2 "10" - /4 "11" - N/A set to /4 for lowest power consumption when idling (recommended) 0 - do not assert SEQ_SLEEP when idling 1 - assert SEQ_SLEEP for minimal analog power when idling record B arm Xenon flash (see 0: 3 CCP_CTRL for firing the flash) record A arm Xenon flash 5 XE_FLASH_EN 0 14:6 15 RESET 0 Address 4 Bits 3-2 Register Name CCP_CONFIG B_CLK_DIV[1:0] Reset Value 0x0000 "00" 5-4 A_CLK_DIV[1:0] "00" 7-6 IDLE_CLK_DIV[1:0] "00" 8 IDLE_SEQ_SLEEP 0 9 10 B_ARM_XE A_ARM_XE 0 0 Document #: 38-19008 Rev. *A Page 16 of 31 PRELIMINARY Address 5 Bits 0 Register Name CCP_GLOBAL LED_FLASH_EN Reset Value 0x0000 0 R/W R/W Clients / Description settings for CCP, SEQ, ISP CYIWOSC1300AA SEQ 0 - LED flash off (also see 0:39 SEQ_FLASH2 for automated flash turn-off) 1 - LED flash on; the switching of the FLASH strobe is not synchronized to the frame capture. SEQ record A horizontal pixel binning 0 - binning off (snapshot mode) 1 - binning on (to be combined with subsampling) SEQ record B horizontal pixel binning 0 - binning off 1 - binning on (to be combined with subsampling) SEQ, ISP, CCP record A subsampling in X and Y 0 - 1:1:1:1:... 1 - 1:1:0:0:1:1:0:0:... 2 - 1:1:0:0:0:0:0:0:1:1:0:0:... 3 - N/A use subsampling when record A is used for video preview (recommended) SEQ, ISP, CCP record B subsampling in X and Y 0 - 1:1:1:1:... 1 - 1:1:0:0:1:1:0:0:... 2 - 1:1:0:0:0:0:0:0:1:1:0:0:... 3 - N/A do not use subsampling when record B is used for snapshot (recommended) SEQ 0 - the frame reset cycle at the start of a Xe flashed acquisition is at normal frame rate (slow) 1 - the frame reset cycle at the start of a Xe flashed acquisition is at accelerated frame rate (fast) to reduce shutter lag. SEQ 0 - analog gain updates immediately take effect (for test/debug only) 1 - gain updates are post-synced to frames to bring them in line with exposure time updates R/W R/Clients / Description CCP status and diagnostics present running status 0 - idle or halting 1 - running 1 2 A_BINNING 0 0 3 B_BINNING 0 5:4 A_SUB[1:0] "00" 7:6 B_SUB[1:0] "00" 8 FAST_RESET 0 10 SEQ_GAIN_SYNC 0 Address 6 Bits 0 Register Name CCP_STAT STAT_RUN Reset Value 0x0000 0 Document #: 38-19008 Rev. *A Page 17 of 31 PRELIMINARY Address 1 Register Name STAT_CTXT Reset Value 0 R/W Clients / Description present record 0 - record A 1 - record B present clock division 0 - /1 1 - /2 2 - /4 3 - not used Sleep mode CYIWOSC1300AA 3:2 STAT_DIV[1:0] "00" 4 15:5 Address 16 STAT_SLEEP Register Name CONFIG2 0 0 Reset Value 0x5F9C R/W R/W Clients / Description sets bias (power) of the ADC recommended value for record A preview, record B snapshot, and low-power idling is 0x5F9B record A ADC bias value for preview: '1' value for snapshot: '0' record A ADC bias value for preview: "1101" value for snapshot: "1110" record B ADC bias value for preview: '1' value for snapshot: '0' record B ADC bias value for preview: "1101" value for snapshot: "1110" Fixed value Fixed value Fixed value Bits 0 A_ADC_FPB_n '0' 4:1 A_ADC_SB_n[3:0] "1110" 5 B_ADC_FPB_n '0' 9:6 B_ADC_SB_n[3:0] "1110" 10 14:11 15 Address 17 CONFIG2A CONFIG2B CONFIG2C Register Name CONFIG3 '1' "1011" '0' Reset Value 0x0077 R/W R/W Clients / Description sets bias (power) of the column amplifiers recommended value for record A preview, record B snapshot, and low-power idling is 0x0073 record A COL bias snapshot value: "0111" preview value: "0011" record B COL bias snapshot value: "0111" preview value: "0011" Fixed value Bits 3:0 A_COL_BIAS[3:0] "0111" 7:4 B_COL_BIAS[3:0] "0111" 11:8 CONFIG3A "0000" Document #: 38-19008 Rev. *A Page 18 of 31 PRELIMINARY Address 18 Register Name CONFIG4 Reset Value 0x0077 R/W R/W Clients / Description CYIWOSC1300AA sets bias (power) of the PGA recommended value for record A preview, record B snapshot, and low-power idling is 0x0073 record A PGA bias snapshot value: "0111" preview value: "0011" record B PGA bias snapshot value: "0111" preview value: "0011" Fixed value Bits 3:0 A_PGA_BIAS[3:0] "0111" 7:4 B_PGA_BIAS[3:0] "0111" 11:8 Address 19 CONFIG4A Register Name CONFIG5 "0000" Reset Value 0x0077 R/W R/W Clients / Description sets bias (power) of the preamp / column amp gain stage recommended value for record A preview, record B snapshot, and low-power idling is 0x0073 record A PRE bias snapshot value: "0111" preview value: "0011" record B PRE bias snapshot value: "0111" preview value: "0011" Fixed value Bits 3:0 A_PRE_BIAS[3:0] "0111" 7:4 B_PRE_BIAS[3:0] "0111" 11:8 Address 22 CONFIG5A Register Name CONFIG6 "0000" Reset Value 0x0777 R/W R/W Clients / Description sets bias for the current reference recommended value for record A preview, record B snapshot, and low-power idling is 0x0777 Fixed value Fixed value spare control port for analog core: SPARE[3:0]: bias for precharge SPARE[4]: use internal resistor for current reference (also see IREF_SELECT) SPARE[7:5]: - Bits 3:0 7:4 15:8 CONFIG6A CONFIG6B SPARE[7:0] "0111" "0111" 0x07 Address 23 Bits 7:0 11:8 15:12 Register Name SEQ_A_FRAMES A_NRFRAMES[7:0] A_BLANK_FIRST[3:0] A_BLANK_PERIOD[3:0] Reset Value 0x0000 0x00 0x0 0x0 R/W R/W Clients / Description record A frame capture sequences record A number of frames to acquire; 128 means neverending, values 0 and above 128 are illegal record A number of frames to blank out after start of acquisition record A number of frames to blank out between any valid frames Document #: 38-19008 Rev. *A Page 19 of 31 PRELIMINARY Address 0:24 Bits 7:0 11:8 15:12 Register Name SEQ_B_FRAMES B_NRFRAMES[7:0] B_BLANK_FIRST[3:0] B_BLANK_PERIOD[3:0] Reset Value 0x0000 0x00 0x0 0x0 R/W R/W Clients / Description CYIWOSC1300AA record B frame capture sequences record B number of frames to acquire; 128 means neverending, values 0 and above 128 are illegal record B number of frames to blank out after start of acquisition record B number of frames to blank out between any valid frames Address 25 Bits 7:0 15:8 Register Name SEQ_A_ORIG A_X1[7:0] A_Y1[7:0] Reset Value 0x0000 0x00 0x00 R/W R/W Clients / Description record A physical frame origin record A address of first pixel to read; multiply by 8 to get the effective address; 0 in normal operation. record A address of first line to read; multiply by 8 to get the effective address; 0 in normal operation. Address 26 Bits 7:0 15:8 Register Name SEQ_B_ORIG B_X1[7:0] B_Y1[7:0] Reset Value 0x0000 0x00 0x00 R/W R/W Clients / Description record B physical frame origin record B address of first pixel to read; multiply by 8 to get the effective address; 0 in normal operation. record B address of first line to read; multiply by 8 to get the effective address; 0 in normal operation. Address 27 Bits 7:0 15:8 Register Name SEQ_A_SIZE A_XD[7:0] A_YD[7:0] Reset Value 0x82A2 162d 130d R/W R/W Clients / Description record A physical frame size record A line length in physical pixels; multiply by 8 to get the effective length; 1296/8 in normal operation. record A frame height in physical lines; multiply by 8 to get the effective length; 1040/8 in normal operation. Address 28 Bits 7:0 15:8 Register Name SEQ_B_SIZE B_XD[7:0] B_YD[7:0] Reset Value 0x82A2 162d 130d R/W R/W Clients / Description record B physical frame size record B line length in physical pixels; multiply by 8 to get the effective length; 1296/8 in normal operation. record B frame height in physical lines; multiply by 8 to get the effective length; 1040/8 in normal operation. Address 29 Bits 7:0 Register Name SEQ_A_ORIG_ROI A_X1_ROI[7:0] Reset Value 0x0101 1d R/W R/W Clients / Description record A Region Of Interest origin record A address of first pixel in ROI (i.e., qualified by LINE on the output interface); multiply by 8 to get the effective address; 8/8 in normal operation. record A address of first line in ROI (i.e., qualified by FRAME on the output interface); multiply by 8 to get the effective address; 8/8 in normal operation. 15:8 A_Y1_ROI[7:0] 1d Document #: 38-19008 Rev. *A Page 20 of 31 PRELIMINARY Address 30 Bits 7:0 15:8 Register Name SEQ_B_ORIG_ROI B_X1_ROI[7:0] B_Y1_ROI[7:0] Reset Value 0x0101 1d 1d R/W R/W Clients / Description CYIWOSC1300AA record B Region Of Interest origin record B address of first pixel in ROI; multiply by 8 to get the effective address; 8/8 in normal operation. record B address of first line in ROI; multiply by 8 to get the effective address; 8/8 in normal operation. Address 31 Bits 7:0 15:8 Register Name SEQ_A_SIZE_ROI A_XD_ROI[7:0] A_YD_ROI[7:0] Reset Value 0x80A0 160d 128d R/W R/W Clients / Description record A physical ROI size record A ROI line length in physical pixels; multiply by 8 to get the effective length; 1280/8 in normal operation. record A ROI frame height in physical lines; multiply by 8 to get the effective length; 1024/8 in normal operation. Address 32 Bits 7:0 15:8 Register Name SEQ_B_SIZE_ROI B_XD_ROI[7:0] B_YD_ROI[7:0] Reset Value 0x80A0 160d 128d R/W R/W Clients / Description record B physical ROI size record B ROI line length in physical pixels; multiply by 8 to get the effective length; 1280/8 in normal operation. record B ROI frame height in physical lines; multiply by 8 to get the effective length; 1024/8 in normal operation. Address 33 Bits 7:0 Register Name SEQ_A_DUMMY A_XD_DUMMY[7:0] Reset Value 0x0100 0d R/W R/W Clients / Description record A number of dummy pixels and lines record A dummy pixels (ref non-subsampled array); multiply by 8 to get the effective number. These pixels are appended at the end of each line, but do not appear at the output. Use this to set desired line time or to clear pipelines in the image signal processor. record A dummy lines (ref non-subsampled array); multiply by 8 to get the effective number. These lines are appended to the frame, but do not appear in the output. Use this to set desired frame time, to clear pipelines in the image signal processor, or to enforce an exposure time in excess of the number of physical lines. Minimum value is 1. 15:8 A_YD_DUMMY[7:0] 1d Address 34 Bits 7:0 Register Name SEQ_B_DUMMY B_XD_DUMMY[7:0] Reset Value 0x0100 0d R/W R/W Clients / Description record B number of dummy pixels and lines record B dummy pixels (ref non-subsampled array); multiply by 8 to get the effective number. These pixels are appended at the end of each line, but do not appear at the output. Use this to set desired line time or to clear pipelines in the image signal processor. record A dummy lines (ref non-subsampled array); multiply by 8 to get the effective number. These lines are appended to the frame, but do not appear in the output. Use this to set desired frame time, to clear pipelines in the image signal processor, or to enforce an exposure time in excess of the number of physical lines. Minimum value is 1. 15:8 B_YD_DUMMY[7:0] 1d Document #: 38-19008 Rev. *A Page 21 of 31 PRELIMINARY Address 38 Bits 5:0 Register Name SEQ_FLASH1 FLASH_DELAY[5:0] Reset Value 0x0041 0x001 R/W R/W Clients / Description Flash configuration 1 CYIWOSC1300AA Xenon flash delay in line times (multiply by 8 for effective number) from the last physical line reset in the fast-reset preamble to the firing of the flash strobe. Note that for Xe flash to be operated the exposure time must be set to its maximum allowed value. Xenon flash strobe burning time in line times, multiply by 8. R/W R/W Clients / Description Flash configuration 2 Xenon flash: first frame after start of imaging sequence for which FLASH is to fire. Xenon flash: number of consecutive frames, up to 13, in which the flash is fired. Values 14 and 15 are illegal. LED flash: number of consecutive frames, up to 13, during which FLASH remains enabled before being extinguished automatically (see AUTO_FLASH). 14 or more means FLASH strobe remains asserted until CCP_GLOBAL.LED_FLASH_EN is deasserted. 11:6 Address 39 Bits 3:0 7:4 FLASH_LENGTH[5:0] Register Name SEQ_FLASH2 FLASH_FIRST[3:0] 0x001 Reset Value 0x0011 0x1 FLASH_NR_FRAMES[3:0] 0x1 Address 40 Bits 1:0 3:2 4 Register Name CONFIG7 CONFIG7A CONFIG7B INV_X Reset Value 0x2F85 "01" "01" '0' R/W R/W Clients / Description Fixed value Fixed value pixel scan direction 0 - straight 1 - inverted line scan direction 0 - straight 1 - inverted Fixed value Fixed value Fixed value Fixed value Fixed value R/W R/W Clients / Description 5 INV_Y '0' 7:6 8 9 12:10 13 Address 41 Bits 0 7:1 9 11:10 15:14 CONFIG7C CONFIG7D CONFIG7E CONFIG7F CONFIG7G Register Name CONFIG8 CONFIG8A CONFIG8B CONFIG8C CONFIG8D ABORT_DUMMY[1:0] "10" '1' '1' "011" '1' Reset Value 0x4C7E '0' 3Fh '0' "11" "01" Fixed value Fixed value Fixed value Fixed value number of dummy lines scanned when frame aborted. Multiply by 8 for the effective number, regardless of subsampling factor. Document #: 38-19008 Rev. *A Page 22 of 31 PRELIMINARY Address 44 Bits 5:0 Register Name SEQ_STATUS BLACK_RESIDUE[5:0] Reset Value 0x0000 0 R/W R/Clients / Description CYIWOSC1300AA black level, status and BIST results readout black signal measured at ADC at the end of the most recent black level calibration Read this register during a frame, or at the end of a frame, to learn its effective black level. X BIST result 100-Hz component detected in light 120-Hz component detected in light 7:6 8 9 Address 45 Bits 11:0 BIST_RESULT[1:0] FL_100_DETECTED FL_120_DETECTED Register Name SEQ_EXP EXPOSURE_TIME[11:0] 0 0 0 Reset Value 0x0400 1024d R/W R/W Clients / Description exposure time setting exposure time, in line times The exposure time should always be between 1 and the total number (physical + dummy) of lines read in the frame. There is no automatic scaling for subsampling: when no dummies are configured, the maximum exposure time for a full frame is 1024, and for a 2:1-subsampled frame 512. The sensor behavior is undefined when illegal values are entered. Changing exposure time will have effect from the second frame on after the present frame. Maximum exposure time = physical + dummy -1 Clients / Description gain and offset settings see CCP_GLOBAL.SEQ_GAIN_SYNC for the automatic synchronization of gain changes with exposure time changes and with frame boundaries. programmable gain amp gain 0 - 1x (nominal) 1 - 1.1x ... 31 - 19 x column amp gain 0 - 1x 1 - 2x 2 - 4x 3 - not used PGA offset generation 0 - use value PGA_OFFSET 1 - use self-calibration PGA offset value for manual mode Address 46 Register Name SEQ_GAIN Reset Value 0x3F80 R/W Bits 4:0 PGA_GAIN[4:0] "00000" 6:5 COL_AMP_GAIN[1:0] "00" 7 PGA_OFFSET_AUTO '1' 14:8 PGA_OFFSET[6:0] 3Fh Document #: 38-19008 Rev. *A Page 23 of 31 PRELIMINARY Address 64 Bits 0 Register Name OUT_CONFIG CLK_POL Reset Value 0x0000 '0' R/W Clients / Description CYIWOSC1300AA Output interface configuration PIX_CLK polarity 0 - straight 1 - inverted FRAME polarity 0 - straight 1 - inverted FRAME timing 0 - with PREFRAME (early) 1 - with FRAME (late) LINE polarity 0 - straight 1 - inverted LINE timing 0 - only ROI lines have LINE asserted 1 - all lines (physical, dummies, ...) have LINE asserted R/W R/W Clients / Description ISP - Defect Pixel 0 - disable defect interpolation, passing on all data unchanged 1 - enable defect interpolation scale factor for defect gradient 0 - 0.5: aggressive interpolation, detects more pixel defects, but may impair picture sharpness 1 - 1.0 2 - 1.5 3 - 2.0: soft interpolation R/W R/W Clients / Description Special register for 8-bit transfer mode 1 FR_POL '0' 2 FR_FORM '0' 3 LN_POL '0' 4 LN_FORM '0' Address 128 Bits 0 Register Name ISP_DEFECT EN_DEFECT_PIXEL Reset Value 0x0002 '0' 2:1 DEF_PIX_SCALE[1:0] "01" Address 241 7:0 Register Name ACCESS_MODE (SPECIAL) byte Reset Value 0x0000 0 Document #: 38-19008 Rev. *A Page 24 of 31 PRELIMINARY 9.0 9.1 CYIWOSC1300AA Feature Descriptions Efficient Well Pixel The Xenon flash can only be used in snapshot mode. The conditions to start the Xenon flash sequence are: * XE_FLASH_EN='1', and * RUN = `1 These bits are all programmable in the CCP_CTRL register. This then will initiate one of the following two possible image capture sequences. The first possible sequence is for the flash to be ignited after the last physical line of the frame has been reset, and before the first physical line is read. This scheme only works when the exposure time is close to the total frame time. Note the long duration between the start of the sequence and the time the first flash is fired. Figure9-1 illustrates a typical Xenon flash frame sequence, including its start-up: First the lines in the frame are all reset. Then, during the run time of the dummy line `resets', the FLASH strobe is asserted. The readout of the first frame starts. The sequence is repeated if so required. The exposure time shall be set to be (almost) equal to the total allowed exposure time (i.e., *_YD + *_YD_DUMMY). The second possible sequence can be seen in Figure9-2. The reset phase for frame 1 is shortened by applying resets to all physical lines as fast as possible. This skews the effective exposure time for frame 1, but also reduces the time elapsed between the start of the sequence and the first firing of the flash. The skewed exposure time is of little consequence as most of the light is captured during the flash burn time. When FAST_RESET is asserted with Xenon flash operation the initial reset sequence for the first frame is shortened: instead of resetting one physical line per nominal line time, all physical lines of the first frame are reset as fast as possible, one after the other. This considerably reduces the time between starting the sequence (`pushing the button') and the readout of the first valid frame. Special Cypress technology allows large volume well capacity. 9.2 Windowing Two windows can be programmed. The first window determines which physical pixels of the array are to be read. The second window lies entirely within the first window, and denotes the actual region of interest to be read out to the user. The difference between both windows is the overscan area, used in setting up the correct boundary conditions of the ROI pixels in all subsequent image processing. 9.3 Subsampling Subsampling can be programmed in X and Y independently, for two schemes that preserve the Bayer-ordering of colors: * 1:1:0:0: two pixels/lines are read, two skipped, for a 2x2 reduction in image size. * 1:1:0:0:0:0:0:0: two pixels/lines are read, six skipped, for a 4x4 reduction in image size. When subsampling is enabled in Y all lines that are skipped are reset to avoid blooming. 9.4 Flash Synchronization A flash strobe signal is generated for LED and Xenon flash types. Start and stop instants and duration are programmable, as well as the frame(s) in which the flash should be triggered. 9.5 Xenon Flash Fixed amplifier gains and exposure time can be programmed for Xenon flash operation, with automatic changeover between flash and non-flash modes. Note: All of the following sequences are preceded by one of the two image capture start sequences with hard reset burst described in a previous section. Xenon flash burn Line reads per frame Line resets per frame Time Shutter time * Frame 1 Frame 1 Dummy 1 Frame 2 * Dummy 1 Dummy 2 Dummy 2 Frame 2 Frame 3 * Dummy 2 Dummy 2 Dummy 3 Frame time Figure 9-1. Xenon Flash Frame Sequence Xenon flash burn Line reads per frame Line resets per frame Time Frame time * Frame 1 Frame 1 Dummy 1 Frame 2 * Dummy 1 Dummy 2 Dummy 2 Frame 2 Frame 3 * Dummy 2 Dummy 2 Dummy 3 Figure 9-2. Xenon Flash Sequence with Accelerated Initial Reset Document #: 38-19008 Rev. *A Page 25 of 31 PRELIMINARY Note that the line time used in generating the dummy idle time is not accelerated, as this is the time gap in which the flash must fire! FLASH_FIRST[3:0] programs the first frame after the start of the sequence prior to whose readout FLASH is to be asserted. FLASH_FIRST = 0 sets this action to the first frame, as in the above pictures. FLASH_N[3:0] programs the number of frames prior to which FLASH must be strobed. FLASH_N = 0 is a reserved value and should not be used. If FLASH_N = 15 FLASH shall be fired before every frame, until either XE_FLASH_EN or RUN is deasserted, or until N_FRAMES have been taken. The instant of firing and the duration of the FLASH strobe can be programmed (See Figure9-3): FLASH_DELAY[7:0] is the time elapsed, in line times, between the reset of the last physical line in the scan window and the assertion of FLASH. FLASH_LENGTH[7:0] is the duration, in line times, during which FLASH remains asserted. It is required that sufficient dummy black lines be configured to allow the flash timing (however, the sequencer is not checking this requirement): FLASH_DELAY + FLASH_LENGTH < *_YD_DUMMY It is recommended that fixed exposure time and gain settings (also white balance settings where applicable) for Xenon flash use are programmed in the record B exposure settings. At the trigger a record change to B is then done. Note that Xenon flashing only works properly if the exposure time is almost equal to the total frame time, and if sufficient black dummy lines are available to house the flash burning time. CYIWOSC1300AA such corrupt images can be seen as a linear combination of an unLEDed image and a LEDed image, this phenomenon can be ignored. White balance should be set to fixed values matched to the LED illuminant. 9.7 Normal Operation Mode When STANDBY and RESET_n are deasserted and a clock CLK is running, the device is in its normal operating mode, capable of receiving commands on its serial bidirectional interface, and of outputting images on its parallel bus. In normal operating mode two further power modes can be distinguished: high-power snapshot and low-power preview. These modes are not hardwired on the device, but are defined by the user in terms of image size, subsampling, output data format and power consumption. The snapshot mode will typically be used for taking delivery-quality pictures, engaged for short periods of time with high image quality at the cost of high power consumption. Preview mode is used most of the time, generating subsampled images at video rate, and at low power consumption. 9.8 Standby Mode When STANDBY is asserted the device is in a power-off state: all outputs and the command interface pins are tri-stated, the core logic is powered off, and analog core and ADC are in lowpower bias mode. Register contents are undefined, and a chip reset is a mandatory part of a changeover to normal operating mode. Inputs to the chip, including CLK, may be driven. The time required to get back from standby mode to normal mode is less than 100 ms. At start-up, STANDBY needs to be deasserted after RESET for the normal image sequence to start. 9.6 LED Flash The LED flash is controlled by the user and typically remains lit over a number of consecutive frames. On/off control can be direct, or off can be programmed to happen a number of frames after the LED was lit. When RUN = `1' the strobe FLASH will be asserted whenever LED_FLASH_EN is seen to be asserted. The FLASH remains active for FLASH_N frames. This frame count is restarted at the instant LED_FLASH_EN is asserted, but also at a record change. FLASH_N has an option to keep FLASH asserted indefinitely, in which case FLASH will be deasserted by the user deasserting FLASH_EN. Due to the action of the rolling shutter, the switching on and off of the LED flash will each give rise to one frame with nonhomogeneous illumination. This is unavoidable. However, as 9.9 Idle Mode The user can program the device to run at a lower clock speed and set the analog core to run at zero bias to reduce power consumption. This mode can be set like the A and B records and behaves like a third record. See the register map for more explanation. In this idle mode grabbing images is not possible. 9.10 Readout Modes The sensor supports two fundamentally different readout modes, one for continuous-time viewfinder operation, one for snapshot operation. Both modes can be custom-tailored through the Camera Control Processor Line resets Line reads Reset of array dummies Readout of frame Flash_delay flashlength FLASH Figure 9-3. Xenon FLASH Strobe Timing Configuration Document #: 38-19008 Rev. *A Page 26 of 31 PRELIMINARY 9.11 Viewfinder Mode CYIWOSC1300AA In viewfinder mode the pixel array is operated in subsampled low-power mode at up to 30 fps, continuously streaming, with rolling shutter operational. The chip's logic can be clocked by fCLK/2 or fCLK/4 compared to the normal fCLK and all timings can be scaled to keep the line and frame time invariant. This mode is soft-configurable through user-writable registers. These registers contain settings for: * analog module bias/power levels * internal system clock divisions A typical user-defined setting for viewfinder mode will be low bias, low power, slow operation, divided clock. number of lines in a frame, and their position, can be programmed. Frame rate increases. This allows the readout of (for example) the 640x512 center area of the 1.3M-pixel array at 30 fps without subsampling. 9.13 Power-on Reset A power-on-reset circuit allows the device to generate an internal chip reset when the power comes up while STANDBY is deasserted, or when power is up while the STANDBY pin gets deasserted and the RESET_n pin is accidentally left floating. Thus, the internal logic reset net can be driven from three different sources/origins: * the POR block * the external pin RESET_n * a user command issued on the serial interface 9.12 Snapshot Mode In snapshot mode the pixel array is typically operated in fullframe full-power mode, during a programmable number of frames and with the rolling shutter operational, continuously streaming. When snapshot mode is entered, an optional accelerated reset of all lines can be generated. The time from entering snapshot mode to the first line of the first available frame is limited to the desired exposure time plus a small overhead period. Windowing to increase frame rate is supported: the 9.14 On-Chip Pixel Binning Binning can be used in all modes however only makes sense in 2-subsampling mode (read 2, skip 2). When horizontal factor-2 subsampling is used, each two pixels of the same color can be summed and output as a single pixel. This reduces aliasing in preview mode. Document #: 38-19008 Rev. *A Page 27 of 31 PRELIMINARY 10.0 1.3MP Imager Pad Numbering I/O PWR GND PWR GND PWR Type Function CYIWOSC1300AA Table 10-1. Pin Map Table (Left Side) PAD # Signal Name 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 VDD_28 DGND VAA_PIX AGND VDD_18_O VDD_18_O Not used REG_BYPASS Not used STANDBY RESET_n CMD_D CMD_CLK CMD_A FLASH Not used FRAME VDDIO GNDIO Not used Not used Not used Not used Not used Not used Not used VAA AGND CMOS CMOS CMOS I2C compatible I2C compatible CMOS CMOS CMOS Raw logic supply in; connect to 2.65-3.1V when regulator is used, otherwise to 1.7-1.9V Logic ground Pixel array supply (2.65-3.1V) Analog/pixel array ground Regulated 1.8V logic supply out (for test and bypass cap only) Regulated 1.8V logic supply out (for test and bypass cap only) Do not use Regulator bypass Do not use Turns off device Asynchronous reset Interface serial data in and out Interface bit clock, up to 400 kHz Interface device address selector Flash strobe Do not use Frame valid strobe IO supply (1.7-3.1V) IO ground Do not use Do not use Do not use Do not use Do not use Do not use Do not use Sensor core/ADC analog supply (2.65-3.1V) Sensor core/ADC analog ground Document #: 38-19008 Rev. *A Page 28 of 31 PRELIMINARY Table 10-2. Pin Map Table (Right Side) PAD # Signal Name 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 Not used Not used Not used PIX_OE CLK LINE PIX_CLK GNDIO VDDIO PIX_D[9] PIX_D[8] PIX_D[7] PIX_D[6] PIX_D[5] PIX_D[4] PIX_D[3] VDDIO GNDIO PIX_D[2] PIX_D[1] PIX_D[0] Not used Not used DGND AGND_DIG VAA_DIG AGND VAA GND GND PWR GND PWR I I O/Z O/Z GND PWR O/Z O/Z O/Z O/Z O/Z O/Z O/Z PWR GND O/Z O/Z O/Z CMOS CMOS CMOS CMOS CMOS CMOS CMOS CMOS CMOS CMOS CMOS CMOS CMOS CMOS I/O Type Do not use Do not use Do not use Output enable for PIX_D/PIX Set to 1 enables outputs, set to 0 tri-states outputs System clock, 4 .. 27MHz Line valid strobe Output pixel data word clock IO ground IO power Output pixel data Output pixel data Output pixel data Output pixel data Output pixel data Output pixel data Output pixel data IO power IO ground Output pixel data Output pixel data Output pixel data Do not use Do not use Logic ground Sensor core/ADC digital ground Sensor core digital supply (2.65-3.1V) Sensor core/ADC analog ground Sensor core/ADC analog supply (2.65-3.1V) Function CYIWOSC1300AA Document #: 38-19008 Rev. *A Page 29 of 31 PRELIMINARY 11.0 11.1 CYIWOSC1300AA Electrical Specifications Absolute Maximum Ratings Storage Temperature: ....................................-40C to 85C Input Voltage: ........................................ -0.2V to VCC +0.2V ESD Susceptibility (HBM): .......................................... 2000V Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 11.2 Operating Conditions Supply Voltage: ........................................... 2.8 and 1.8VDC Operating Temperature: ............................... -20C to +70C 11.3 Electrical Characteristics The following specifications apply for T A = 25C Table 11-1. Parameter Vdd Vaa P15, SXGA ISBE Digital I/O VIO VIO VOH18 VOL18 VIO VIO VIH18 VIL18 ILOAD CIN COUT PCLK max tr, tf Output level [high] Output level [low] Output level [high] Output level [low] Input level [high] Input level [low] Input level [high] Input level [low] Input leakage current Input capacitance Output capacitance Pixel Output rate Rise / Fall time Vdd-IO - 0.7 Vdd-IO - 0.3 Vdd-IO - 0.4 0.4 V V V V V V V V A pF pF MHz ns Description Digital Supply voltage Analog Supply voltage Active power consumption Stand-by current consumption Full frame 15 fps 10-bit resolution Conditions Min. 1.7 2.65 Typ. 1.8 2.8 100 TBD Max. 1.9 3.1 Unit V V mW mA 12.0 Environmental Specifications Specification Value Comment See performance specifications for sensitivity de-rating over temperature Table 12-1. Operating Temperature -20C to 70C Storage Temperature Humidity Salt Mist Atmosphere Dust Chemical Resistance All products and company names mentioned in this document may be the trademarks of their respective holders. -40C to 85C 90% relative humidity @ 60C 100 mg/m3 Document #: 38-19008 Rev. *A Page 30 of 31 PRELIMINARY Document History Page Document Title: CYIWOSC1300AA 1.3 Megapixel CMOS Sensor] Document Number: 38-19008 REV. ** *A ECN NO. 354077 392759 Issue Date See ECN See ECN Orig. of Change HBH New data sheet HBH CYIWOSC1300AA Description of Change Added detail to meet final product specifications Document #: 38-19008 Rev. *A Page 31 of 31 (c) Cypress Semiconductor Corporation, 2005. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or oth er rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to res ult in significant injury to the user. The inclusion of Cypress |
Price & Availability of CYIWOSC1300AA
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |